How to Build a Sabung Ayam Pit That Meets International Standards

HOW TO BUILD A SABUNG AYAM PIT THAT MEETS INTERNATIONAL STANDARDS

BUILDING THE FOUNDATION FOR SAFETY AND FAIR PLAY

USE 12-INCH REINFORCED CONCRETE FOR THE BASE SLAB

Pour a 12-inch thick slab with ½-inch rebar spaced every 8 inches in a grid pattern. This prevents cracking under the weight of spectators and repeated impacts from sparring roosters.

INSTALL A 3-FOOT DEEP GRAVEL DRAINAGE BED BENEATH THE SLAB

Lay 12 inches of compacted gravel, then 12 inches of sand, topped with a 6-mil vapor barrier before pouring concrete. This stops groundwater from seeping up and keeps the pit dry during heavy tropical rains.

SET THE PIT FLOOR 6 INCHES BELOW GROUND LEVEL

Dig the pit area 18 inches deep, then pour the slab so the finished floor sits 6 inches below surrounding ground. This creates a natural barrier that keeps roosters from accidentally jumping out mid-match.

FRAME THE PIT WALLS WITH 4-INCH CMU BLOCKS

Use 8-inch tall concrete masonry units (CMUs) laid in running bond with type-S mortar. Fill every third core with rebar and concrete to resist lateral pressure from crowds leaning on the walls.

DESIGNING FOR OPTIMAL VIEWING AND VENTILATION

KEEP THE INNER DIAMETER AT EXACTLY 20 FEET

A 20-foot circle gives roosters enough space to maneuver without allowing them to retreat too far. Mark the center with a 1-inch steel pin, then use a 10-foot string to scribe the perfect circle before digging.

BUILD A 30-INCH HIGH WALL WITH A 15-DEGREE INWARD ANGLE

Lay the first course of CMUs flat, then tilt each subsequent course inward by ¼ inch per course. This angle prevents roosters from flapping onto the wall and gives spectators a better view of footwork.

INSTALL 4-INCH PVC VENTS EVERY 4 FEET AROUND THE PERIMETER

Cut 4-inch holes through the CMU walls at 4-foot intervals, then insert schedule-40 PVC pipes sloped downward to the outside. Cover the exterior ends with ¼-inch hardware cloth to keep rodents out while allowing airflow.

ADD A 6-FOOT WIDE CONCRETE APRON AROUND THE PIT EDGE

Pour a 4-inch thick concrete apron sloped at 2% away from the pit. This gives handlers a stable footing and prevents mud from being tracked into the fighting area during wet weather.

ENSURING COMPLIANCE WITH INTERNATIONAL REGULATIONS

USE NON-SLIP EPOXY COATING ON THE PIT FLOOR

Apply a two-part epoxy coating mixed with 30-grit aluminum oxide aggregate. This creates a textured surface that prevents roosters from losing footing without being abrasive to their feet.

INSTALL A 42-INCH HIGH SPECTATOR RAILING WITH 2-INCH SPACING

Build a railing using 1½-inch schedule-40 steel pipe with vertical balusters spaced no more than 2 inches apart. This meets international safety standards for preventing children from falling into the pit.

MOUNT A 12-INCH WIDE LED LIGHT STRIP AT 8 FEET HIGH

Install waterproof LED strips around the entire perimeter, angled downward at 45 degrees. This provides even lighting without shadows, which is required for video recording matches for international judging.

CREATE A 3-FOOT WIDE GATE WITH A DOUBLE-LATCH SYSTEM

Build a gate using 1-inch steel square tubing with a top and bottom latch that must be operated simultaneously. This prevents accidental openings while allowing quick exit in emergencies.

BUILD A SEPARATE 4X4 FOOT SCORING TABLE PLATFORM

Construct a raised platform 30 inches high with a 4×4 foot surface, positioned outside the pit but within 6 feet of the edge. This gives judges an unobstructed view while keeping them at a safe distance.

INSTALL A 1-INCH DIAMETER DRAIN IN THE CENTER OF THE PIT

Drill a 1-inch hole through the slab and install a brass drain fitting connected to a 2-inch PVC pipe that slopes to a gravel dry well. This allows quick cleanup between matches without leaving standing water.

ADD A 6-INCH HIGH KICKBOARD AROUND THE PIT FLOOR

Attach a 6-inch tall, ½-inch thick HDPE kickboard to the inside of the pit walls using stainless steel screws. This protects the lower courses of CMUs from damage when roosters strike the walls.

USE INTERLOCKING RUBBER MATS FOR THE FIGHTING SURFACE

Cover the entire pit floor with ¾-inch thick interlocking rubber mats designed for horse stalls. These provide consistent footing, reduce leg injuries, and can be easily replaced when worn.

INSTALL A 2-INCH THICK SOUND-ABSORBING PANEL ON THE CEILING

If the pit is covered, mount 2-inch thick acoustic panels to the ceiling using resilient channels. This reduces echo and crowd noise, which is required for clear audio recording during international broadcasts.

BUILD A 3X3 FOOT FIRST AID STATION WITHIN 10 FEET OF THE PIT

Construct a small cabinet with a lockable door, stocked with antiseptic, gauze, vet wrap, and a digital thermometer. This meets international regulations for immediate medical response during matches. https://malkis4d.tech/.

Leave a Reply

Your email address will not be published. Required fields are marked *